Hawkeye Goshawk Manuel d'utilisateur télécharger pdf

1/2 TURN

TO STOP

Installation of Electronic

Cover Plate

► 9/16 Open-end wrench

(for Redtail)

► 1/2 Open-end wrench

(for Roadside)

Installation onto Gauge Head

► 7 / 16 Open End Wrench

Calibration (Zero & Span)

► Connections to you PLC or a

Fluke 780 (or Eq.) 24 VDC

Loop Calibrator

► 1/8” Blade screwdriver

This document contains the recommended basic procedures installing and calibrating the Hawkeye Industries Goshawk Level Transmitter

for use on a Redtail or Roadside Gauge Head. For more comprehensive instructions, please refer to the Goshawk Operation and Trou-

bleshooing Guide.

Requirements

The gauge board, indicator, float, and gauge head, shall be in

place per their respective installation instructions prior to Goshawk

installation.

Tools

Parts Required

Goshawk Installation on Gauge Head

TANK PREPARATION | GAUGE BOARD KIT INSTALLATION | FLOAT GUIDE KIT INSTALLATION | GAUGE HEAD INSTALLATION | GOSHAWK INSTALLATION

Quick Start Installation Instructions

Goshawk Level Transmitter

QTY Part

► 1 Goshawk Level Transmitter

► 2 1/4-20 UNC x 3/4 Hex Cap screw (included)

Installation on Redtail

► 1 Redtail Gauge Head with

► 1 Redtail Electronic Cover Plate installed

Installation on Roadside

► 1 Roadside Gauge Head with:

► 1 Roadside Electronic Cover Plate installed

If the electronic cover plate is not already installed, remove the standard

cover plate from the Indicator (Open) side of the gauge head, and replace

with the appropriate Electronic Cover Plate for your gauge head.

Turn the indicator cable spool IN THE EMPTYING DIRECTION (CLOCK-

WISE) until the the indicator is in the empty position (top of gauge board).

Immobilize the spool. (cover omitted for clarity)

Goshawk Quick Installation Instructions, March 2014. Replaces May 2012 document

Turn the Transition Coupler on the Goshawk Transmitter IN THE EMPTY-

ING DIRECTION (COUNTER-CLOCKWISE) until it stops. DO NOT OVER

TURN, AS DAMAGE WILL OCCUR. Then turn the Transition Coupler on

the Goshawk Transmitter IN THE FILLING DIRECTION (CLOCKWISE)

one-half turn

Aligning the tangs on the transmitter with the cover plate bolt holes and

fasten with the 1/4 NC Hex Cap Screws. Ensure the transition coupler

mates with the gauge head axle without binding by turning the reel a few

times before tightly securing the transmitter to the cover plate.

REDTAIL

ROADSIDE

REDTAIL

ROADSIDE

1 2

Résumé du contenu

Page 1 - Goshawk Level Transmitter

1/2 TURN TO STOPInstallation of ElectronicCover Plate► 9/16 Open-end wrench (for Redtail) ► 1/2 Open-end wrench (for Roadside) Installation onto Gauge

Page 2 - Calibration

Hawkeye Industries Inc.2Loop Power ConnectionsAfter removing the transmitter cover, the PCB will be visible. Run the conductors from the conduit port

Plus de documents pour Capteurs Hawkeye Goshawk

Voir le document Hawkeye Goshawk Manuel d'utilisateur

Hawkeye Goshawk Manuel d'utilisateur (4 pages)

Commentaires sur ces manuels

Pas de commentaire

Hawkeye Goshawk Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Hawkeye Goshawk. Hawkeye Goshawk User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Capteurs Hawkeye Goshawk

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Hawkeye Goshawk